XR33152

Documentation

• Datasheet

  • ±60V Fault Tolerant 3.0V to 5.5V RS-485/RS-422 Transceivers

• Application Notes

  • ANI-23 Fault Tolerant Testing

• Product Flyer

  • ±60V Fault Tolerant RS-485 Transceivers

• Product Brochure

  • Interface Brochure

• Whitepapers

  • How Robust Is Your Fault Tolerant Transceiver?

Application

Packaging

Parts & Purchasing

Quality & Environmental Data

Click on the links above to download the Certificate of Non-Use of Hazardous Substances.

Support

Search our list of FAQs for answers to common technical questions.
For material content, environmental, quality and reliability questions review the Quality tab or visit our Quality page.
For ordering information and general customer service visit our Contact Us page.

Frequently Asked Questions

What is the maximum cable length and data rate for RS-232 and RS-485 / RS-422?

For RS-232 it is 50 feet (15 meters), or the cable length equal to a capacitance of 2500 pF, at a maximum transmission rate of 19.2kbps. When we reduce the baud rate, it allows for longer cable length. For Example:

 

Baud Rate (bps)	Maximum RS-232 Cable Length (ft)
19200	50
9600	500
4800	1000
2400	3000

 

For RS-485 / RS-422 the data rate can exceed 10Mbps depending on the cable length. A cable length of 15 meters (50 feet) will do a maximum of 10Mbps. A cable length of 1200 meters (4000 feet) will do a maximum of 90kbps over 24 AWG gauge twisted pair cable (with 10 pF/ft). Refer to Annex A TIA/EIA-422-B.

 

 

What are the advantages of RS-422/RS-485 over RS-232?

As RS-422/RS-485 uses differential signaling, it is more immune to noise and longer cables and/or high data rates can be used, especially in noisy environments. Also, RS-485 allows for multi-point operation, up to 32 unit loads. Transceivers may use a fraction of a unit load, increasing the number of devices on the bus. For example, the XR33152 receiver input impedance is at least 120 kΩ, which equates to 1/10 of a unit load. Therefore, XR33152 allows more than 320 devices (32 x 10) on the bus.

What is RS-485 / RS-422 fail safe?

Fail Safe is an attempt to keep the output of the RS-485 receiver to a known state. Transceivers may have standard fail safe or advanced / enhanced receiver fail safe features. Standard fail safe supports open inputs while enhanced fail safe transceivers such as the SP339 and XR34350 support open input, shorted input and undriven terminated lines without external biasing. See Application Note ANI-22 for more detail.

 

Figure 1:  Standard Failsafe Receiver Sensitivity Range

 

 

 

Figure 2: Standard Failsafe with Open Input

 

 

 

Figure 3: Enhanced Failsafe Receiver Sensitivity Range

 

 

 

Figure 4:  Enhanced Failsafe with Open Input

 

 

 

Figure 5:  Enhanced Failsafe with Shorted Input

 

 

 

Figure 6:  Enhanced Failsafe with Un-driven terminated lines

 

 

 

How can I obtain an evaluation board?

Find the product page of the part that you want to get an evaluation board for and click on Parts & Purchasing. Example:

 

Find the icons under Buy Now or Order Samples:

 

 

Click on the Buy Now icon and see who has stock and click on the Buy button:

 

 

 

Alternatively, you can click on the Order Samples

 

 

If the icons are missing, then contact Customer Support.

Can one RS-485 driver / receiver pair be used for several microcontrollers to communicate to a host PC?

Yes, this is possible using one RS-485 transceiver. The microcontrollers will have to be addressable and have tri-state outputs. The RS-485 device can be controlled by the host via the DE/RE pin. The micros will have to be in either receiving mode or tri-state mode when the RS-485 transceiver is transmitting data. When the host transmits it will have to send an address to the specific micro. If any micro transmits the transceiver will have to be in receiving mode and all other micros will have to be in receive or tri-state. So the host would have to initiate this sequence by addressing the micro first then switch the transceiver to receive.

The half duplex system would have a bus with one transceiver and multiple microcontrollers all tied to the bus. For 5V systems the SP485 family can be used. For 3V systems the SP3070 family can be used. The require speed will determine the part number. The SP3078 part runs up to speeds of 16Mbps.  See the parametric search on https://www.exar.com/products/interface/serial-transceivers/rs485-422 for more options.

Care must be taken to assure the transceiver can drive the multiple micros in RX mode.

Are your parts 100% tested for ESD?

ESD tests are “destructive tests.” The part is tested until it suffers damage. Therefore parts cannot be 100% tested in production, instead a sample of parts are characterized during the product qualification. The test procedure consists of “zapping” pins with a given voltage using the appropriate model and then running the part through electrical tests to check for functionality or performance degradation.

How much ESD voltage could a part see in normal use?

ESD is caused by static electricity. In order for an ESD event to occur there must be a buildup of static charge. Very high charge levels are actually quite rare. In a normal factory environment, taking basic ESD precautions (grounding-straps, anti-static smocks, ionizers, humidity control, etc.) static levels can be kept below a few tens of volts. In an uncontrolled environment, like an office, static levels rarely get above 2000 volts. Under some worstcase conditions (wearing synthetic fabrics, rubbing against synthetic upholstered furniture, extremely low humidity)

levels can go as high as 12 to 15 thousand volts. Actually to get to 15000 volts or higher you would need to be in an uncomfortably dry environment (humidity below 10%) otherwise static charge will naturally dissipate through corona discharge. It would definitely be considered a “bad hair day.” Humans can generally feel a static shock only above 3000 volts. A discharge greater than 4000 volts can cause an audible “pop.” But repeated lower level discharges can be imperceptible and still may have a cumulative damaging effect on sensitive ICs. All ICs, even those with robust protection, can be damaged if they are hit hard enough or often enough.

Why are some pins protected to higher ESD levels than others?

Most ICs in a typical system are at greatest risk of ESD damage in the factory when the PCB is assembled and the system is being built. After the system is put together they are soldered onto the PCB and shielded within a metal or plastic system enclosure. Interface ICs are designed to attach to an external connector that could be exposed to ESD when a cable is plugged in or when a person or object touches the connector. These interface pins are most likely to see ESD exposure and therefore benefit from additional protection.

Some RS-485 transceiver part numbers look similar to each other but they have an “E” in the part number. Others do not. What does the E mean?

Actually the letter “E” could have two different meanings, depending on where it is in the part number. Most of our interface devices are available in different temperature grades. Commercial temperature (0 to 70C) has a “C” after the numeric part number. Industrial-extended temperature (-40 to +85C) use the letter E. So for example SP485CN is commercial and SP485EN is industrial. The second letter indicates the package type, in this case N for narrow-SOIC. Another E in the suffix indicates that this device has enhanced ESD protection, typically of ±15000Volts on the interface pins. Devices that do not have the enhanced ESD still contain built-in ESD protection of at least ±2000Volts. For example the SP485ECN is ESD rated up to ±15kV, and the SP485CN is rated for ±2kV HBM.

What does the -F suffix on the part number mean?

The -F suffix indicates ROHS / Green compliance:
https://www.exar.com/quality-assurance-and-reliability/lead-free-program

How can I find out if the status of a part number is EOL / obsolete or active?

The best way to determine this is to go to maxlinear.com and type the part into the search function. At or near the top of the results you should see something that looks like:

 

 

 

In this example, we looked for XRA1201. Click on part number header or on the link at the bottom of the result.  This brings you to the product page. For example:

 

 

 

Click on Parts & Purchasing, highlighted with the blue arrow above. The screen changes to:

 

 

 

Notice the status column and the “Show obsolete parts” link.  A legend tells you the definition of the different statuses. Click on the “Show obsolete parts” link to see EOL or OBS part numbers along with the Active part numbers, the legend still present:

 

 

 

Another method to find out if a part is OBS or EOL is to click on SUPPORT at the top:

 

 

 

And then Product Change Notifications:

 

  

 

Type the part into the search, and click on one of the part numbers from the drop down menu. Then you can look for the Product Discontinuation Notice, which generally is at the top of the list, for example:

 

 

 

If you see this, it tells you that this particular orderable part has been discontinued and when the last order date is, or was. If you click on the file, then you can view the notice we sent about this if you purchased the part in the recent past. It may also advise of a replacement part. When an orderable part first becomes discontinued, Product Discontinuation Notices are sent are sent to those who have purchased the parts in the recent past, if purchased directly, with a dated opportunity to place a last order.

Submit a Technical Support Question As a New Question