|Information||Five Output Universal PMIC|
|# of Outputs||4|
|VIN MIN (V)||4.0|
|VIN MAX (V)||5.5|
|VOUT MIN (V)||3.0V / 1.3V / 0.8V / 0.6V|
|VOUT MAX (V)||3.6V / 1.92V / 1.6V / 1.4V|
|Set Point Resolution (mV)||20mV / 20mV / 6.25mV / 6.25mV|
|Gate Drive Pull Up/Down||1.5A / 1.5A / 2.5A / 4A|
|Programmable Frequency Range (MHz)||1 to 2|
|Control Technology||Current Mode PWM|
|NVM Technology||Factory Only|
|Junction Temp Range (°C)||-40 to 125|
|Special Features||2 configurable power good outputs; LDO and 2-Input 8-bit ADC, Temp Monitoring, I2C controllable, Supported by Excel configuration tool|
|PowerArchitect Version#||Excel Config Tool|
The MxL7704-B is a five output Universal PMIC optimized for powering low power FPGAs, DSPs, and microprocessors from 5V inputs. Four synchronous step down buck regulators range from 1.5A system power to 4A core power.
A 100mA LDO provides a clean 3.3V power for auxiliary devices. All of the outputs support ±10% margining. The two highest power outputs also support dynamic voltage control which saves power in processors that can use this function. You can monitor an input voltage flag and PGOOD flags for each output through a 400kHz I2C interface. The I2C port can enable you to modify the power up and down sequencing options, assign PGOOD outputs to the PGOOD pins, enable outputs, and select switching frequency.
The high switching frequency and current mode architecture with internal compensation enable a very fast transient response to line and load changes without sacrificing stability and keeping board space to a minimum.
The MxL7704-B built-in one-time programmable (OTP) memory stores key startup configurations. It reduces the external components typically used to set output voltage and sequence of regulators. Regulator parameters are adjustable through high-speed I2C after the start up which offers flexibility for different system states.
The fault protection features include input undervoltage lockout, overcurrent protection, and thermal protection. The MxL7704-B is offered in a 5mm x 5mm QFN package.
- Input voltage range: 4.0V to 5.5V
- Four Synchronous Buck Regulators
- Internally compensated current mode
- 1MHz to 2.1MHz switching frequency
- Buck 1: 3.0V to 3.6V, 20mV step, 1.5A
- Buck 2: 1.3V to 1.92V, 20mV step, 1.5A
- Buck 3: 0.8V to 1.6V, 6.25mV step, 2.5A
- Buck 4: 0.6V to 1.4V, 6.25mV step, 4A
- 100mA LDO 3.3V
- ±2% maximum total DC output error over line, load, and temperature
- 3.3V/5V 400kHz I2C interface
- Dynamic voltage scaling
- Status monitoring by channel
- Sequencing control
- Input voltage status register
- Highly flexible conditional sequencing engine with external input
- 2 configurable PGOOD outputs
- Adjustable switching frequency
- 5mm x 5mm 32-pin QFN package
- Supported by Excel Configuration Tool
- Low power processor, ASIC and FPGA power
- Industrial control
- Test equipment
- POS terminals
Documentation & Design Tools
|Data Sheets||MxL7704-B Five Output Universal PMIC||R02||September 2023||1.9 MB|
|Product Flyers||Power Management & Interface Products for Cable, Satellite and IP STB/Home Gateway||March 2018||2 MB|
|Configuration Tools||MxL7704 Configuration Tool Rev 2.0||2.0||March 2019||675.5 KB|
|Product Brochures||Power Management Brochure||October 2020||2.4 MB|
Parts & Purchasing
|Part Number||Pkg Code||Min Temp||Max Temp||Status||Suggested Replacement||Buy Now||Order Samples||PDN|
|MXL7704-BQB-T||QFN32 5x5 OPT4||-40||125||Active||Order|
Active - the part is released for sale, standard product.
EOL (End of Life) - the part is no longer being manufactured, there may or may not be inventory still in stock.
CF (Contact Factory) - the part is still active but customers should check with the factory for availability. Longer lead-times may apply.
PRE (Pre-introduction) - the part has not been introduced or the part number is an early version available for sample only.
OBS (Obsolete) - the part is no longer being manufactured and may not be ordered.
NRND (Not Recommended for New Designs) - the part is not recommended for new designs.